- The middle half earn between $23.47 and $43.81 an hour.
- Indiana ranks 21st of the 50 states with published figures for median pay in this trade.
- Indiana pays more than 1 of its 4 neighboring states.
- BLS counts about 4,580 sheet metal workers on payrolls in Indiana.
- At the state median wage, a sheet metal or HVAC business needs to bill about $124.66 an hour on the labor rate calculator's starting numbers.
Sheet Metal Worker pay in Indiana, bottom to top
Sheet metal workers fabricate and install ductwork, flashing, gutters and metal roofing parts, in a shop and on site.
| Pay level | Hourly | Yearly | National hourly |
|---|---|---|---|
| 10th percentile | $20.49 | $42,620 | $18.57 |
| 25th percentile | $23.47 | $48,820 | $22.99 |
| Median | $30.79 | $64,040 | $29.71 |
| 75th percentile | $43.81 | $91,130 | $39.24 |
| 90th percentile | $50.04 | $104,080 | $50.79 |
| Average (mean) | $33.67 | $70,030 | $32.62 |
Pay is bunched up in Indiana. The top tenth earn $50.04 an hour or more, about 2.4 times the $20.49 at the bottom tenth. Nationally that gap is 2.7 times, so the step from the bottom of the scale to the top is shorter here than in most places.
The floor is higher than nationally ($20.49 against $18.57) but the ceiling is lower ($50.04 against $50.79), which squeezes pay toward the middle.
The average wage, $33.67, sits 9% above the median. A smaller group of higher earners pulls the average up, so the median is the better guide to what a typical sheet metal worker makes.
How Indiana compares with other states
Over a full year the gap to the national median is small: $64,040 in Indiana against $61,800 nationally, $2,240 more.
In the state ranking, Indiana sits 21st, between Nebraska ($30.98) and Missouri ($30.56). The range runs from $22.03 in Arkansas to $47.38 in Washington.
Against its neighboring states, Indiana is in the middle: Illinois, Michigan and Ohio pay more, and Kentucky pays less.
How many sheet metal workers work in Indiana
BLS estimates 4,580 sheet metal workers on payrolls in Indiana, 3.8% of the 119,770 nationwide. Only 4 states have more.
The trade is a bigger part of the local job market than it is nationally: 1.4 of every 1,000 jobs in Indiana, 1.9 times the national share.
What a sheet metal or HVAC business in Indiana should charge
Say you run a sheet metal or HVAC business in Indiana and pay the state median of $30.79 an hour. Here is the labor rate calculator's math on its starting numbers: 40-hour weeks, 10 paid days off, 2 unbilled hours a day, 7.65% payroll taxes, $90,000 a year of overhead and 15% profit.
| Step | Math | Result |
|---|---|---|
| Paid hours | 40 × 52 | 2,080 |
| Hours at work | 2,080 − 10 days × 8 | 2,000 |
| Billable hours | 2,000 × 6 ÷ 8 | 1,500 |
| Labor cost | $30.79 × 2,080 × 1.0765 | $68,943 |
| Break-even rate | ($68,943 + $90,000) ÷ 1,500 | $105.96 |
| Rate with 15% profit | $105.96 ÷ 0.85 | $124.66 |
That is $124.66 per billable hour, 4 times the wage, and $1.90 more than the $122.76 the same math gives at the national median wage.
Paying the 75th percentile instead, $43.81 in Indiana, to hire and keep experienced people raises the rate to $147.53.
A cheaper crew saves less than it seems: at the 25th percentile wage of $23.47, the rate only drops to $111.81.
Overhead, at $60 of every billed hour, and the unbilled hours move this rate more than a raise does. A dollar more in wages adds about $1.76 to the rate.
Run it with your own numbers in the labor rate calculator. It is free and shows every step.
Where these numbers come from
Source: U.S. Bureau of Labor Statistics, Occupational Employment and Wage Statistics, May 2025.
The figures are the BLS state estimates for SOC 47-2211, sheet metal workers, across all industries, read straight from the May 2025 state data file. They cover wage and salary workers, not the self-employed. Where BLS did not publish a figure, this page leaves it out.
All states in one table: sheet metal worker salary by state.